min co te c nh o l og y lab s, in c . ? ? ? mtl2400ru mtl2420ru (electrically similar to hcc240/hcc242) features: ? high reliability ? base lead eliminated for improved noise immunity ? rugged surface mount package ? stability over wide temperature ? +1kv electrical isolation applications: ? eliminate ground loops ? level shifting ? line receiver ? switching power supplies ? motor control description the mtl2400ru & mtl2420ru contain a proton tolerant led optically coupled to a silicon planar phototransistor. the optocoupler is built in a 4 pin leadless chip carrier. this optocoupler is capable of transmitting signals between two galvanic sources. the potential difference between transmitter and receiver should not go over the maximum isolation voltage. the internal base connection has been eliminated for improved noise immunity. absolute maxi mum rati ngs input to output voltage ............................................................................................................................... .................................................................... 1000v emit ter-collec tor volt age ...................................................................................................... .................................................................................................5v collector-emitter voltage (value applies to emitter-base open-circuited & the input-diode equal to zero) ........................................ 30v reverse input voltage ............................................................................................................................... ............................................................................2v input diode continuous forward current at (or below) 65c free-air temperature (see note 1) .......................................................40ma peak forward input current (value applies for tw < 1 s , prr < 300 pps) ......................................................................................................1a continuous collector current ............................................................................................................................... ..........................................................50ma continuous transistor power dissipation at (or below) 25c free-air temperature (see note 2) .................................................. 300mw st orage temperat ure............................................................................................................ ...................................................................... -65 c t o + 150c operating free-air temperature range ............................................................................................................................... ..................-55 c t o + 125c lead solder temperature (10 seconds max.) ............................................................................................................................... ........................ 240c notes: 1. derate linearly to 125c free-air temperature at the rate of 0.67 ma/c above 65c. 2. derate linearly to 125c free-air temperature at the rate of 3 mw/c. recommended operati ng condi ti ons: parameter symbol mi n max uni ts input current, low level i fl 01 a input current, high level i fh 210 ma supply voltage v ce 550 v operating temperature t a -55 125 c selection guide part number part descri pti on mtl24x0u.001.x single channel optocoupler, commercial (0 to+70c operating temperature range) mtl24xou.002.x single channel optocoupler, commercial (-40 to +85c operating temperature range) mtl24x0u.003.x single channel optocoupler, commercial (-55 to +100c operating temperature range) mtl24x0u.004.x single channel optocoupler, screened to jantx level (-55 to +100c operating temperature range) note: replace first x with 0 or 2 to indicate type of part required. x at end of part number represents lead finish. replace with a for gol d or s for solder.
min co te c nh o l og y lab s, in c . ? ? ? mtl2400ru & mtl2420ru si ngle channel optocoupler electri cal characteri sti cs t a = 25 c unless otherwise specified. parameter symbol mi n typ max uni ts test condi ti ons input diode static reverse current i r 100 a v r = 2.0v input diode static forward voltage v f 1.68 2.0 v i f = 10ma input diode static forward voltage -55 cv f 2.1 v i f = 10ma input diode static forward voltage +100 cv f 2.0 v i f = 10ma output transi stor t a = 25 c unless otherwise specified. parameter symbol mi n typ max uni ts test condi ti ons collector-emitter breakdown voltage v (br)ceo 30 v i c = 1ma, i b = 0, i f = 0 emitter-collector breakdown voltage v (br)eco 5vi c = 0ma, i e = 100 a, i f = 0 collector-emitter dark current +100 c i ceo1 i ceo2 100 100 na na v ce = 20v, i f = 0ma v ce = 20v, i f = 0ma coupled characteristics t a = 25 c unless otherwise specified. parameter symbol mi n typ max uni ts test condi ti ons on state collector current mtl2400u mtl2420u i c(on) 0.15 0.40 ma v ce = 5v, i f = 2.0ma on state collector current mtl2400u mtl2420u i c(on) 2.5 10 8 15 ma v ce = 5v, i f = 10ma on state collector current mtl2400u mtl2420u i c(on) 1.0 4.0 ma v ce = 5v, i f = 10ma, t a = -55 c on state collector current mtl2400u mtl2420u i c(on) 1.0 4.0 ma v ce = 5v, i f = 10ma, t a = +100 c collector-emitter saturation voltage mtl2400u mtl2420u v ce(sat ) 0.3 0.3 v v i f = 20ma, i c = 2.5ma i f = 20ma, i c = 10ma isolation resistance r iso 10 11 ? v in-out = 1000v input to output capacitance c io 2 5.0 pf f = 1mhz rise time mtl2400u mtl2420u t r 15 20 s v cc = 10v, i f = 10.0ma, r l = 100 ? fall time mtl2400u mtl2420u t f 15 20 s v cc = 10v, i f = 10.0ma, r l = 100 ? package dimensions schematic diagram
|
